Overview

There are advantages in knowing the various Roper dryer parts. For one thing, you know which parts are in dire need of cleaning. It is also easier to tell which parts are faulty should the machine break down on you.

As you probably know, the cost for dryer repair is steep. And there is no guarantee that your dryer will work quite as seamlessly as before once the repair is finished. In most cases, you will only need to have some parts replaced. Your knowledge on these Roper dryer parts will come handy when you experience some problems with your washer.

Dryer Door And Washer Lid Switch

This is one of the safety features of this brand of dryer. It is a simple mechanism that goes on and off and prevents the machine from working and operating when the door is left open. Just in case your children play with your dryer, you can be assured of their safety.

The switch costs less then $17. Replacing it is not that difficult. First, you have to check if it is really the switch that is not working. You can try starting the dryer and open the drum door. If it is still working, the switch is the problem. You can replace the part by prying open the main control panel. There you can find the lid switch. Do not remove the screws. Just loosen them up so you can extract the switch. After you have removed the broken one, install the new one. Tighten the screws and then secure the main control panel again.

Heating Element Connection

In Roper dryer parts, this is the one that comes with a yellow-colored wire nut. If your dryer is not heating up, the problem could be in this dryer part. First, you need to disconnect the vent of the dryer. Unplug the power supply. Get a nutdriver and then carefully loosen up and remove the nuts that secure it. Now take off the damaged heating element. Put a new one and then secure it back using the nuts. Install the vent once again and plug the dryer.

Gas Dryer Burner

This is one of the Roper dryer parts found in gas dryers. It is usually twenty four inches in length. Its replacement is kind of pricey. Usually, it costs more than $200. Replacing it in your dryer can be complicated too. This is usually done by a professional to avoid accidents.

Thermal Cut Off

This part controls the temperature. It has a high limit thermostat with about 25 degrees Fahrenheit of limit and a fuse with 360 degrees Fahrenheit limit. Replacement for this part costs more than $30. If you cannot control the temperature of your dryer or there is an inaccuracy of the dryer temperature, this might be the problem.

Once you have purchased new Roper dryer parts, try to install a new one. Remove the back cover. There are a lot of screws securing it so you should prepare a small box to put all the screws in. Remove the attachment of the wires to the high limit thermostat and the cut-off fuse. These parts are usually included in the replacement kit. There are four screws securing these two parts. Once you have extracted them, you can put the new one and reconnect the screws. Attach the wires to the same way the previous kit was attached. Once you have completed this procedure, you can replace the back cover.

Dryer Exhaust

The exhaust is responsible for purging out used hot air in the dryer. This will control the temperature in your dryer while it is working. Replacing it will cost no more than $40. You can change the exhaust if the current dryer exhaust is too big for your dryer cabinet.

You need to open up the front panel of your dryer. Using a screwdriver, remove the screws that secure the back part. The entire back part should be removed. The kit comes with a manual. Just remove the old rear exhaust of your dryer and then use a new one. For those people installing their dryers in a cabinet, you can try using the elbow shaped left exhaust. Replace the old one with this new one.

Conclusion

Unlike other dryers, it is not that difficult to find Roper dryer parts. Thanks to their merging with Whirlpool Company, these dryers and their parts are more accessible. Easy installation guide is also provided for you. As you might have figured out earlier, the replacement of some of these parts can be done even without the help of an expert. You just have to familiarize yourself with the different parts of the dryer and how they can affect the dryer mechanisms when they break down.

Back from Roper Dryer Parts to Roper Washing Machine

Back from Roper Washer to Washing Machine Reviews