Most of the Maytag washer problems are caused by Maytag washer timer failure. The timer of a washing machine is what sets the programming cycles in motion. If this is not working properly, the machine will fail to advance to the next washing cycle.

One of the reasons why this problem always happens with washing machines is because of the link between the timer motor and the timer of the cam. This is always what is wrong with the timer problems. You can usually find the Maytag washer timer at the back portion of the control know of the cycles. There is a program inside the timer. It is placed in a cam and it is usually operated using a switch. When the motor of the timer turns the cam, the switch will also turn. This will turn on and off in order to operate the agitator. This is responsible for facilitating the fill, spin and drain functions of the machine.

How To Test The Maytag Washer Timer

Before you replace the old timer with a new one, make sure it is really malfunctioning. To find out if this is really the faulty part, you will need a volt/ohm meter with alligator clips to test the timer. Disconnect the two leads of the timer and connect it to the volt/ohm meter. Place the meter setting to RX1. If the meter reads zero, then the timer is still working perfectly. If not, you should have it replaced.

How To Remove The Maytag Washer Timer From The Machine

You should purchase a new timer before trying to work on your machine. After purchasing, remove the old timer. Here are the steps you should follow:

1. Before doing anything with your machine, make sure you unplug it first. Wait for a few minutes before trying to fix it. This way, undercurrents have already passed and dissipated. Make sure you mop up pools of water.

2. Get a small screwdriver with a flat head or use a knife to pry the round metal insert located in the control knob of the timer. Pry it carefully and do not break the control knob.

3. There is a small clip holding to the timer shaft. Slide it off the timer shaft. The knob, the dial and the spring will be released. Now carefully remove these parts of the timer and place them in a small box. You will assemble them later so you have to prevent the parts from getting lost.

4. Now remove the back cover of the control panel. There are usually two screws holding them together. You can remove them using a screwdriver. Also remove the screws that hold the front console of the timer. Make sure you know the right position of the timer so you can return it back to its original position.

5. Now that the timer is released, you can wire it up and transfer the one to the old one.

How To Wire The New Maytag Washer Timer

1. Pull the wires off the old timer from the upper left corner of the timer. Push those wires to the new timer. Make sure you place them one wire at a time. Follow the same format as the old timer. You might want to take a photo of the old positioning of the wiring so you can have a basis. But if not, you can use the markings on the terminal lug for reference.

2. Now make sure the lid switch is clicking properly when you close the washer lid. Usually, timer and lid switch problems cause inability of the washer to follow programming settings. You can adjust the switch by adjusting the screws right below the timer.

3. Place your new timer on the back of your console. Screw it tightly back on the console.

4. Now put the knob, the spring and the dial of the new timer. Clip it back on and place back the cover plate. Screw the cover plate in place.

5. Now test the timer back. Use the same method as earlier. Use your volt/ohm meter. It should read zero this time.

6. Try plugging your washer back on and testing the machine. Run an empty washing cycle and find out if the machine is going to transition to the washing stage.

The timer is a key element in the faultless running of your machine. Maintenance of this is necessary. Now that you know how to check if the timer is working, you should do this quarterly to solve common washing machine problems.

Back from Maytag Washer Timer to Best Washing Machine Reviews

Maytag performa washer series feature top load washing machines that are more capable of cleaning and washing your clothes. Top load machines are less efficient than front loaders. However, Maytag makes the most durable and the most reliable machines.

Maytag is known for the durability of their washers. Many of their top loaders last for many generations. That is the main reason why people buy this brand of washer. But find out today what the Maytag Performa washing machine is really capable of doing.

Features Of The Maytag Performa Washer

Here are the core features of this washing machine:

• Six Point Suspension System – This suspension system will allow smooth operation in the washing machine. Most top loaders produce a lot of noise especially during the spin cycle. But this feature will ensure that the machine will work as quietly as possible. This lessens clothing imbalance in the washer drum.
• Large Dual Action Agitator – This dual action agitator can clean your clothes to the core. According to consumers, this machine can make white clothes even whiter. Because of the dual action agitator, the stains are removed.
• More Durable Deep Smooth Polymer Washtub – Maytag used durable materials especially for its wash tub so it will not eventually rust or chip. More often than not, the washtub is the reason for snag fabrics and the accumulation of lint.
• Complete with Bleach and fabric softener dispensers.
• Large drum capacity – You can wash large laundry loads in one washing setting. This is an ideal choice even for those with large families.
• Temperature controls and settings. It also has a setting for permanent press feature.

Pros and Cons of Using Maytag Performa Washer

Many people like its large drum capacity. Although it is a top load washer, it does not scrimp on space. You can wash oversize laundry loads such as comforter and bed sheets. This is also a very quiet series. Due to its suspension system, you can clean without being disturbed by the unnecessary noise in the machine.

The softener dispenser of this machine is also found in the agitator. This infuses the fabric softener better so your clothes will come out softer and more fragrant. You will also like the pebbled sides of the washer tub. This prevents snagging and lint formation.

The downside of this machine is its bleach dispenser. According to some consumers, the machine does not use up all the bleach when needed. As a result, some bleach residues are left in the dispenser. This also runs during your next load. You might inadvertently bleach some colored garments.

The rubber seal also tends to get a little moldy. You have to keep the rubber seal dry all the time so molds will not grow easily. Also, you might not be able to dump last minute clothes once you have already started the washing cycle.

Should You Buy The Maytag Performa Washer?

Despite the bleach dispenser problems of this machine, many people still rated it highly. The durability of this machine is its finest point. According to consumers, this machine lasted longer than their previous brand of top load washer. Also, it does not cost a lot to buy this machine.

This is a good machine to buy. If you are on a tight budget, you can choose this machine instead. Buy from a reliable store. They should give you a reasonable warranty.

How To Take Care Of This Machine?

There were also a lot of complaints for this machine. But that is pretty normal in the washing business. If you know how to take good care of your washer, you can prevent washer problems from appearing soon.

Clean your machine regularly. You might want to dry up the machine as well after using it. Use a clean towel to dry up the rubber seal. This will prevent molds accumulation. Do not over use the machine by washing too many clothes in one cycle. This might only damage the agitator of the machine. It will also cause lint formation.

Also clean the water filters regularly. Clogged water filters can cause low water pressure. It is ideal to clean your water filter at least once a month to ensure that water will flow in continuously.

Also check the belt drive of the motor. If it is already worn out, the machine might not spin and wash effectively. The belt drive is the one that sets the motion of the washer drum. You can purchase a spare belt drive so you can immediately replace it with a new one if it suddenly breaks down on you.

Back from Maytag Performa Washer to Maytag Washers

Back from Maytag Washing Machines to Best Washing Machine Reviews

Maytag Neptune TL washer is one of those top loaders created by Maytag Company in recent years. The industry of top load washers is still very much alive. Many people rely on a top loader more because this is a cheaper alternative. Although they are not as efficient as front loaders, this machine is still a good choice.

When it comes to Maytag, there is a combination of good and bad reviews. There are people who say this is the most durable machine they have tried while there are others who will say that this machine breaks down easily.

The only way to know if the Neptune top load washer is ideal is to learn more about its features and what people are saying about it.

Maytag Neptune TL Washer Features

Here are some of the features you can find in this machine:

• It has a stainless steel washtub that prevents snagging and lint accumulation. It prolongs the life of your garments.
• Front Panel Electronic Controls – The electronic controls are found at the front of the machine for easier access. You can now gain access to the machine with ease.
• Time Remaining Indicator – This will tell you how much more time you are going to wait before the cycle finishes. This way, you can do your other chores without babysitting or checking on your washer too often.
• TurboClean Wash System – This feature will get rid of deep-seated dirt and stains from your clothes. This will make sure that your clothes will come out clean all the time.
• IntelliFill Water Level Sensor – Top loading machines are not regarded as efficient washers but this sensor makes this top loader a lot more efficient that other top loaders in the market. This will control the level of water inside.
• Washing Cycles – There are various washing cycles for your various clothes washing needs.

Pros And Cons Of The Maytag Neptune TL Washer Models

One of the most ideal advantages of using this machine is its quiet functions. Maytag has incorporated smooth balance suspension system that will balance out clothes loads. An imbalance of laundry load is usually the reason for washing machine noise.

This machine also uses low energy. It cuts back on energy consumption better than other top loaders out there. This machine is also quite simple to use. With its control panel found at the front part of the machine, you can easily do your laundry.

What is most ideal about this machine is the missing agitator. It does not use agitator to clean clothes. The whole drum will spin clothes in order to clean, wash, rinse and then dry. This cleaning action is better for your clothes. However, many users say that the missing agitator tends to tangle up their garments right after the cleaning cycle. But this little inconvenience is nothing if you want a bigger drum capacity. The agitator tends to occupy a large space inside the drum. Since it is no longer present, you have more space for your clothes.

One of its downsides is its water usage. Some people say that it does not accurately use the right amount of water to clean clothes. Sometimes, the machine does not rinse clothes properly. Soap suds might still cling on your clothes.

Should You Buy A Maytag Neptune TL Washer?

With the features and the price of this machine, I don’t see any reason why you should not give it a try. It does a better job of cleaning your clothes without using too much energy and water compared to other top loaders.

If you are looking for a washer that can clean better and can clean more clothes in one washing cycle, this is a good choice.

How To Take Care Of Your Maytag Neptune TL Washer

Since the machine does not use an agitator, it uses a special kind of friction inside that will clean clothes effectively. You need to change your detergent to an HE detergent. This will prevent the excessive production of suds. Perhaps one of the reasons why some consumers say the machine does not get rid of suds is because of the use of the wrong detergent. Ordinary detergent creates a lot of suds compared to the HE ones.

Also clean your washer regularly. Run an empty water cycle once a month and add one cup of white vinegar. This will get rid of accumulated molds, mildew and even detergent inside the machine. This will make sure that you will not experience moldy washer problems, clogging and leaking. Maintenance is really necessary so you can make the most out of your Maytag washing machine.

Back from Maytag Neptune TL Washer to Best Washing Machine Reviews

Maytag legacy series are top load washers and dryers that are made to specifically cater to the clothes washing needs for those who are on a tight budget. These laundry appliances are affordable. Maytag is known for their ability to produce durable washing machines. Some of their vintage washers that were created in World War II have been passed down from generations to generations.

However, this durability streak seemed to have escaped the Maytag Legacy Series. There are some complaints about this washing machine. Common washer problems have been experienced.

Problem #1 – The Washing Machine Will Fill Up But It Does Not Immediately Go To The Washing Cycle

This problem happens when the washing machine fills up with water but the function gets trapped in there. The machine will not immediately transition in the washing cycle. It also does not go to the rinse or spin cycle.

More often than not, this problem is caused by a lid switch problem. You have to check the lid switch if it has been really closed. Sometimes, the lid can be closed but the switch is not kicking in.

You can also try checking if the machine is creating a lot of noise. If it is noisy, then it is caused by a problem in the drive belt. Siphon the excess water out first. You can do this by levelling the drain hose lower than the water level. Once the water is completely removed, you can open up the motor part where the motor is usually seen. Check the belt for signs of deterioration. If the belt is already worn out, you should have it replaced.

Problem #2 – The Washer Is Leaking Especially When It Is Already In The Cool Down Rinse Cycle

This Maytag legacy series problem happens quite a lot. There are a couple of things you can do to solve this. Use a screw driver to extract the 2 screws found at the bottom of the front panel of the machine. Once you have already removed the front panel, you can have access to the tub. Find the small hose. This is usually located on the left part of the washer tub. This is the hose that is connected to the bleach dispenser. This is usually the leaking part. Check the hose and connect it properly to the bleach dispenser. If the hose is already damaged, you can replace it with a new one.

Problem #3 – The Washer Produces A Lot Of Noise Especially When It Spins And It Is Leaking At The Bottom

This Maytag Legacy series problem is usually a little difficult to troubleshoot on your own. The noise might be caused by the worn out drive belt of the machine. You need to replace the drive belt with a new one. The leaky problem might be caused by a defective main centre bearing. However, this problem is a lot more difficult to deal with. You need the help of a professional. You can try asking for a price from three repair people. If it is a little pricey to have your machine repaired, you might as well buy a new one.

Problem #4 – The Agitator Spins But The Drum Does Not Spin During The Spin Cycle

The transmission is usually defective. Check the drive belt first. Check for signs of wear and tear. Always replace a defective belt. Once you have replaced the drive belt, check the machine if it is already spinning during the spin cycle.

Problem #5 – The Machine Is Not Spinning And It Is Starting To Smell Like Burned Out Motor

Use your screw driver and open the back door of the machine. Check the machine if it is overheating. If this happens, you should have the motor replaced. However, you need to know the specific model of your washer so you can find the appropriate motor.

Also check the washer drum. Use your hands to move the drum. If it is rotating freely, the drive belt is not working. The belt should stop it from rotating freely.

You also have to take good care of your Maytag legacy series if you want to prolong its life. Clean your washer and get rid of molds in order to reduce clogging. Also check the water hoses of your washer. Replace necessary hose if you want to prevent clogging.

More often than not, washer problems appear also because of poor maintenance. So aside from knowing how to troubleshoot your washer problems, also find out how you can maintain it properly.

Back from Maytag Legacy Series to Maytag Washers

Back from Maytag Legacy Series to Best Washing Machine Reviews

Maytag front load washer is what you need for more efficient clothes washing. There are a lot of front load brands today. But why should you choose Maytag?

Perhaps the main reason why you should pick this brand of washer aside from its obvious efficiency is because of the durability that is a trademark of Maytag. Maytag has had its fair share of washer complaints. But they are also one of those washer brands that have produced machines that will last for a very long time.

Maytag is one of the oldest manufacturers of washing machines. Their products date back to the second world war. There is no denying the fact that when it comes to the washer business, they know the ins and outs.

We looked in on the various front loaders offered by this company and here are our top 5 choices:

Maytag Front Load Washer: MHWE300VW Performance Series

This washing machine clearly embodies its title. It really does provide a good performance to its users. With its NSF Certified sanitization cycles, you can get rid of common household allergens clinging on your clothes and in your washer. This machine also has a SuperSize capacity. This capacity can let you wash large laundry loads in just one washing cycle so you can clean without having to spend a lot of time doing more than one cleaning batch.

This front loader also has an IntelliTemp Automatic Temperature control. Its intelligent features can effectively use the right temperature of water to clean your clothes well. You would not have to use the hot water cycle if your clothes are relatively clean. It also has IntelliFill Automatic Water Level Sensor. This feature will use only the right level of water to clean your clothes well. This will prevent overusage of water.

In addition to that, here are some more of the features of this Maytag machine:

• Smooth Balance Suspension System for quieter functions
• Sensor Controlled Suds Detection for more efficient washing cycle
• Timed release detergent system

Maytag Front Load Washer – Maytag Epic Series

The Epic series is one of the latest developments of Maytag. This machine has a unique Rainfall clean wash system with Sensi-Care Technology. The rainfall system washes the clothes by imitating the motion of rain. This will evenly wash and rinse your clothes. The Sensi-Care technology will automatically detect the amount of dirt in your clothes so the machine can use only the right water to clean out garments.

This machine comes with 10 automatic wash cycles so you can choose from a lot of programming presets for your different types of clothes. It also has a MaxExtract Extended Spin. This feature will speed up the spin cycle during the last 10 minutes of the cycle. It will get rid of more moisture in your clothes so your garments will be dry enough after the spin cycle.

Maytag Front Load Washer MAH2400A

If you are looking for a more compact washing machine, this is the right choice. This machine has the right footprint that can fit smaller living spaces. But despite its small footprint, it still offers comparatively large drum space so you can clean your clothes well.

It also has reliable features such as TurboClean Wash System that is often found in commercial washers. This will get rid of deep-seated dirt and stains in your clothes. This also features Flexible Installation so you can install your washer with ease even with the constraints of small living space. This machine also has an IntelliFill automatic water level that control the amount of water filled up to the washer drum.

Maytag Front Load WasherE550WJ

This washing machine is one of the commercial front loader models of Maytag. This machine has a dynamic venting technology. It keeps your washer and your clothes dry. It also has an allergen removal steam feature that will make your clothes as free from germs and allergens as possible. This machine also has a smooth balance suspension system that will help keep your laundry operations as quietly as possible.

Maytag Front Load Machine MHWE950WW

For those people looking for a washing machine that can really get rid of even the most stubborn dirt and stains, this is the right washer to choose. It has an oxi treat stain-fighting option that can get rid of stains right away. It is also complete with intelligent features that can lessen your consumption of energy and water. This machine also has a power wash cycle that can effectively and evenly clean large laundry loads.

Back from Maytag Front Load Washer to Best Washing Machine Reviews

Maytag Neptune problems with the dryer happen. This is why it is absolutely advisable to constantly check your dryer parts to ensure proper functioning all the time.

However, dryers are not meant to last forever. There will be situations wherein your dryer will break down on you. Before that happens, you should know how to determine the error and what possible solutions you can try.

My Maytag Neptune Does Not Heat Up

There are a couple of reasons why you are experiencing one of the most common Maytag Neptune problems—trouble heating up. The first one is because of a faulty thermal fuse. If the thermal fuse is switched on or off incorrectly, you should have it replaced.

You can purchase this part for $10 per piece. The thermal fuse is responsible for regulating temperature inside the dryer. If it senses that the temperature is turning up too much, it aborts the operation. As a result, it will not completely dry your clothes.

Moisture Control Sensor Of My Dryer Does Not Light Up

The moisture control sensor will determine the amount of moisture in your clothes and find out how long the drying time needed is.

If this does not work, you cannot efficiently dry your clothes. Sometimes, the dryer will also overdry your clothes. The first thing you need to do is to check the ventilation of your dryer. Slowly pull it forward from the wall where you have installed it. Unplug the dryer first. Carefully remove the exhaust hose.

While the exhaust hose is detached, plug the dryer again and run a short drying load. If it is working, there might be something clogging our exhaust hose. Lint may have accumulated in the dryer. You need to remove clogged particles by using a shop vacuum.

Water Is Collecting In The Dryer Drum

This is one of the most common Maytag Neptune problems for their dryers. When water is collecting inside the dryer drum, check the exhaust pipes. If the pipes are directed outside the house, rainfall can seep in and then it will flow inside the drum. You should install the dryer exhaust pipes downwards so that it will not catch rainfall from the outside.

In another case, this can be caused by dryer condensation. If air is not properly recycled in ventless dryers, condensed air can turn into moisture and will leave pools of water in your dryer drum.

My Dryer Shakes, Vibrates And Produces Unnecessary Noise All The Time

This is also one of the most common Maytag Neptune problems today most likely because owners do not know how to maintain the efficiency of their dryers. One reason why your dryer produces noise is because of clogged exhaust, dirty exhaust fan and deteriorating drum rolling bearings. Some dryer models, especially Maytag Neptune models have no lint trap.

This is actually one of its design flaws. As a result, lint can accumulate in the exhaust pipe and the fan. To remove the accumulated lint, unplug the dryer and remove it from the wall. Disconnect the exhaust pipe and remove the lint using a shop vacuum. You can purchase this from the hardware store. Use a soft-bristled brush to clean the fan.

For drum bearings, check if there are signs of deterioration on it. You should have it replaced right away before it breaks down for good. Replacement costs less than $20. In addition to this, do not use the top area of the dryer as a storage area. Dryers need open space because they work with the air around them. Remove anything that may obstruct the flow of air especially if you are using vented dryers.

Common Problems with Maytag Dryer # 5: My dryer does not tumble

Maytag Neptune problems usually happen because of malfunctioning dryer belt. If the dryer belt is bad, the machine will refuse to tumble. It will only heat up. If this happens, you will have unevenly dried-up clothes.

Unplug the dryer and pull it away from the wall. Check the dryer belt. If there are kinks, smooth it out. But if you see signs of deterioration, you should have it replaced immediately. Depending on the type of belt your dryer is using, it can cost roughly around $18-$20.

These Maytag Neptune problems can happen to you. So be prepared on how you can solve these common problems so you can save time and money.

Back from Maytag Neptune Problems to Maytag Washers

Back from Maytag Washing Machines to Washing Machine Reviews

Maytag dryers are efficient and reliable according to their vast number of customers. Maytag is better known in the laundry industry because of their laundry appliances that can help you do your laundry work with ease. What is great about Maytag is that they have been in this business for quite some time now so they know the ins and outs of this business.

Maytag dryers have the features that can help you save time, energy and money in drying your clothes. We need the most efficient dryers today because these electric appliances consume a lot of energy. Appliances that use a heating element usually gobble up big on electricity.

Maytag Dryers Vs Kenmore Dryers

Actually, both Maytag and Kenmore are not under the ownership of Whirlpool company. But despite that, there are a lot of major differences. Maytag is better known for their durability while Kenmore is known for their economical price. In my case, I would rather go for durability than price. But that’s just me.

Sometimes, Maytag is also off in the line of durability. Some people say that Kenmore dryers are more reliable. What gives Maytag an edge is its construction and technology. They provide dryers that can perform top notch. Most of their washers are incorporated with Smooth Balance suspension system. The construction is very sturdy as well. Maytag is a better choice because their domestic dryers are equipped with commercial technology. You can dry your clothes as efficiently as you do in a Laundromat.

Maytag Dryers Vs. Whirlpool Dryers

Maytag does not stand a chance with Whirlpool’s cutting edge technology. Whirlpool is a bigger company to begin with and the fact that Maytag is now under Whirlpool company says a lot about their reputation in the appliance market. But there is also a reason why Maytag is still favored by many consumers. They like this brand of dryer because it has straightforward mechanisms. Whirlpool may offer cutting edge technology that is a tad more energy efficient but this same technology can shorten its life span.

Maytag is still a more durable choice. Although it does not lack in modern features as well. Their newer models of dryers have GentleBreeze drying system with IntelliDry Sensor features. This feature will dry clothes up without ruining the fabric of your clothes. The IntelliDry sensor will also help measure the right amount of drying time needed.

Maytag Dryers Vs. GE Dryers

GE is not a force to reckon with in the laundry industry judging from its general reviews and ratings. They might excel in other electronics niche but Maytag still eclipses their dryers performance-wise. GE has modern features to boast of but so does Maytag. The downfall of GE is probably in its construction. These dryers are prone to failures and breakage.

There are some customers that like GE dryers but not as much as those people that hate these dryers. We still go back to durability mainly because this is an important trait in appliances.

Maytag Dryers Vs. LG Dryers

Arguably the tightest competition of Maytag in the laundry scene is LG. LG not only offers cutting edge technology and efficiency, most of their washers are also durable. The brains behind the dryers of LG made the dryer drum a lot more resistant to wear and tear. That is thanks to the newest direct drive motor technology. LG also comes complete with various sensors that can cut back on drying time. Their machines have been equipped with a mind of its own so you don’t have to baby sit your laundry as it dries in the dryer.

The edge of Maytag over LG is most likely its simplicity and its large drum capacity. Maytag is still considered a modern machine but in comparison to LG, it lacks the bells and whistles. But because of that, it is more likely to last longer than LG dryers. It is also keeping a close distance when it comes to modern features. In addition to those features mentioned earlier, it has 120-minute wrinkle prevent option that keeps your clothes free from creases and wrinkles. This way, you no longer need to use your clothes iron. Maytag also has super capacity. Its large drum capacity is ideal for the use of larger families.

There is only but a small difference when it comes to price. For LG dryers, it can cost roughly around $1000-$1200. For Maytag dryers, be prepared to shell out $900-$1000. Obviously, you can save more money when you buy from Maytag.

Back from Maytag Dryers to Maytag Washers

Back from Maytag Washing Machines to Washing Machine Reviews

Being well-informed about the different Maytag dryer parts can help you stay one step ahead of dryer problems. This will also help make maintenance a lot easier. Do-it-yourself repair is possible if you know your way in the mechanisms of the dryer.

Maytag dryer parts are similar to other dryer parts. But that still depends on the model you are using. Vented and Ventless dryers have some distinct differences. Vented dryers usually have exhaust fans and duct for the air to pass out of the dryer drum. Gas dryers and electricity dryers also have some differences.

The best thing you can do is to familiarize yourself with the dryer user manual. Find out what dryer parts are present in the model of dryer you have.

To help you determine the right parts and their uses, check out the following:

Maytag Dryer Part: Dryer Belt

Nearly all dryers have drive belts. Some of the modern dryers do not use belt. It is similar to a belt you use to hold your jeans in place. It is characterized by rib and grooves count. If the dryer belt is malfunctioning, the drum itself will not tumble. If it still tumbles, the machine produces unnecessary noise and vibrating motions.

If this is the problem, you should check the belt for signs of wear. Usually, you can do the replacement on your own as long as you stick carefully to the step by step procedure. But if you do not trust yourself to do this, better leave the task to a repair man.

Maytag Dryer Part: Thermal Fuse

This usually looks like a white tube-like plastic with two sockets. They are also called thermal cutoffs and these are electrical switches that are used to hamper the flow of electricity when the dryer heats up to the designated “trip” temperature.

If your dryer is not producing enough heat, the problem might be in the thermal fuse. However, according to many repair experts, the problem is not usually with the fuse itself. It just shuts down currency flow because there might be clogging in the vent system that insulates heat inside the dryer. This is to prevent the machine from causing fire. This is your home’s saving grace.

Some thermal fuse systems can be reset. But for Maytag, you are going to have to replace it if it is malfunctioning. To find out if your dryer’s thermal fuse is malfunctioning, you can set the power of the dryer down and then try to bypass the thermal fuse. Power it up your dryer while jumpering or bypassing the thermal device. If your dryer heats up suddenly, it means the fuse is open and you need to have it replaced.

Maytag Dryer Part: Gas Valve

These are tiny circular objects used to run a gas dryer. Replacement costs roughly around $10 per gas valve. This has two coils, also called solenoids. The coils are used top open up the gas chambers inside the valves of your dryer. If one of these coils malfunctions, you cannot ignite the gas chamber. As a result, the dryer won’t heat up. You can tell when it is bad if the igniter suddenly starts glowing.

Maytag Dryer Part: Heating Element

This is a square-like solve circuit responsible for the main heating process of your Maytag dryer. Around it are coils of wire usually made from chrome allow and nickel. These are the wires that transmit and controls the electric current. When current flows into it, heat is produced. This is seen in electric dryers.

Replacing it depends on your Maytag dryer model. Usually, you need to remove the assembly of your dryer so you can so you can replace the heating element. It also depends on what exactly is wrong. Sometimes, you need only to replace the coils if the heating element assembly is still working. Use a screw driver to remove the heating element from the dryer.

Maytag Dryer Part: Dryer Drum Roller With Bearing

When this part breaks down, it usually causes the dryer to produce squealing sounds while working. According to experts, worn out drum roller bearing is usually the cause of the dryer problem. Sometimes, you need only to replace the bearing. In other cases, the whole dryer drum roller with the bearing is replaced.

The bearing often gets damaged as you use your dryer. Replacing it is nearly inevitable. It costs roughly around $25. It is a little expensive so you have to check the model of your Maytag dryer to find the right model for dryer drum roller.

Back from Maytag Dryer Parts to Maytag Washers

Back from Maytag Washing Machines  to Washing Machine Reviews

Maytag dryer is one of the most reliable brands of dryers today. But that does not mean that you have to buy randomly. You have to do careful research first so you can find the most ideal one.

Having said that, there are a couple of things you should consider before sealing the deal. The first part is knowing what features are beneficial for your clothes drying needs. When you have gotten that issue out of the way, you will then find out a reliable store to buy your Maytag dryer. If you can’t buy it directly from Maytag, you should purchase it from a good and reliable appliance store.

What To Look Out For?

Now that we know the important of scrutinizing the dryers we are buying, here are some of the things we should look for:

1. Energy Efficiency

Before that, you have the option of choosing gas or electric dryers. Gas dryers dry up faster than the electric ones but electric dryers are more convenient to use. They are also safer since current is regulated through its thermal fuse. Because of that, you will most likely go for electric dryers. The first thing you need to consider is how efficient the dryer is. How much energy does it consume per load? That will depend on how dry your clothes are in the first place. If your washer’s spin cycle is fast, your clothes are pretty dry by now.

But for energy efficiency, get your yellow sticker energy rating guide to compare energy consumption. Dryers are usually the ones that consume a lot of energy so you need to choose the one that will consume the least. Also look for those with sensors. These sensors will determine the moisture content of your laundry so it can measure how much time is needed to dry your clothes completely. It will cut back on drying time by simply knowing the exact amount of time needed.

Wrinkle-free features also help in cutting back energy consumption. If your clothes dries up without any wrinkles on them, you don’t have to use clothes iron.

2. Drum Capacity

Some people might naturally go for larger drum capacity if they have heaps of laundry loads every time. But the thing is, you should not get one with the biggest capacity. You should get one with the right capacity. If you are using a Maytag dryer with very large capacity and you are only drying a few articles of clothes, it will take some time to heat up the dryer drum because of the extra space inside. As a result, it will take longer time to dry your small load of clothing. If you have a large family, it is wise to choose those with 7 kilograms of dryer capacity. This is just enough for a large family.

Do not scrimp on dryer space either. You might feel more inclined to purchase portable dryers because they are easier to install and to move around but their drum capacity might not be large enough. As a result, you need to do a second batch of clothes drying. Some people tend to overstuff their dryers with clothes because of lack of space. As a result, the dryer does not perform well, lint accumulates faster and the heating element of the dryer malfunctions.

3. Anti Microbial and Anti Allergen Features

Drying and sanitizing your clothes at the same time is ideal especially if you have a baby at home. Baby clothes have to remain allergen-free so as not to expose your little one to possible allergen threats. Since moist clothes are prone to mold and bacterial formation, you need a dryer that can dry up clothes fast. There are now dryers that use up steam to refresh and sanitize the laundry load. You might want to look for these Maytag dryer models.

Conclusion

It is not that difficult to find an ideal Maytag dryer. You just have to know what features you are looking for so you do not inadvertently buy something with excessive features you don’t need and dryers with lacking features. When you are already in the appliance store, don’t be pressured into buying even if the sales representative is hounding you. Take your time choosing and make sure you are given a lot of options.

Ask about their Maytag dryer models and find out which one fits your budget and your specifications well. Remember that you will need a good and reliable dryer for the next few years so you really have to be more vigilant.

Back from Maytag Dryer to Washing Machine Reviews

1. How to re-level your Maytag Neptune Washer?

As you know, not re-levelling your washing machine can cause it to vibrate, shake and produce noise incessantly. Some washers even vibrate and shakes hard enough that the whole machine literally walks. Here is what you need to do:
a. Ask someone to carefully tilt the machine so you can gain access to its front feet. Make sure you tilt it back not more than 4 inches as excess water in the pipes might leak to the motor area.
b. You should have prepared a small wood block with 2 x 4 dimensions. Place this woodblock under the center of your Maytag washer.
c. Using an adjustable wrench, loosen up the locknut of the feet of your washers. When the locknuts are loosened up, you can already adjust the feet. After you have adjusted it, tighten the locknuts once again. You can also purchase some of those rubber soles sold cheaply in the market. This will help secure the washer in place.
d. Remove the wood block and slowly put the washer back into its original position. If you have a level carpenter tool, use it to check its balance.
e. Also purchase a platform to secure the foot of your washer.

2. How To Reset Maytag Neptune TL Washer?

There will be times when you just want to reset your Maytag Neptune washer. This will probably not accomplish anything but it can refresh timer settings and all those programmable functions to help you key in the right controls. Since there are no reset buttons for washing machines, you can turn off the washer and unplug it. Also disconnect the hose. You might need to push the washer forward to uninstall it from the wall. Remove the back hoses using your hands or pliers. Make sure you have a towel ready to catch excess water. Leave it unplugged for about 5 minutes. After 5 minutes, attach the hoses back on and then plug it.

3. What To Do With Mold Problem?

If you have a moldy washing machine, run an empty washing cycle in the highest water temperature level. Add a cup of white vinegar and a cup of baking soda. Do not use baking soda for cold water settings because they will not fully dissolve. Let the mixture dissolve. This will help remove not only molds from the drain pipes and the washer drum, this will also get rid of lime deposits. When they cycle has finish, run an extra rinse cycle to remove residues. Wipe the washer interior with clean towel and open the drum door. Molds will not form if your washer is completely dry.

4. I Can’t Find The Lint Trap On My Maytag Neptune Washer?

Most Maytag Neptune models do not have lint filter. This is a design flaw. Chances are, lint may already be clogging your drain pipes, water filter and water valves. You might have to open the drain pipes and use a shop vacuum to get rid of accumulated lint. After than, run an empty water cycle and add a cup of white vinegar. This will also help wash off other accumulated residues that may cause your washer to malfunction.

5. Maytag Neptune Washer Cuts Off On Rinse Cycle Only? What Should I Do?

If your washer stops after the rinse cycle, there could be a problem with its control switch. These washers are programmed to perform to the data sent by the control switch. If your washer function aborts in the rinse cycle, the control switch might not be receiving data from the spin cycle program.

According to many consumers, Neptune washers are prone to electrical issues. However, this is not something you can fix on your own. Rather than try to the control switch, you have to hire a repairman to do the job. If you don’t have money for repairs yet, You just have to manually wring out excess water from your laundry and hang them to dry completely.

These are the common Maytag Neptune washer maintenance tips. In addition to that, always keep your washer free from soap residues. Clean it regularly. Also, check hoses and belt for kinks or signs of deterioration. This way, you will be one step ahead of the washer problem.

Back from Maytag Neptune Washer to Maytag Washers

Back from Maytag Washing Machines to Washing Machine Reviews